Battery For 2017 Ford Fusion

Share This Post

When Replacing The Battery Keep In Mind:

How to: Install a New Battery on a 2017 Ford Fusion
  • The quality of the electrical connections to the battery posts is important. Connections must be clean, free of corrosion and properly tightened.
  • Batteries store a large amount of energy and if short-circuited a battery could explode and can create intense discharges that can damage your eyesight. Insulated tools should be used to attach cabling to battery terminals. Otherwise, the batterys positive cable can be shorted to ground or the positive and negative posts can be directly shorted. Batteries can only be safely installed from a positive terminal to positive wiring and from a negative terminal to body ground. If the polarity is reversed damage will likely occur to the vehicles electrical system.
  • Generally, a car battery will have a service life of 4 to 7 years. If a load test on a battery reveals a significant reduction in the capacity of the battery to provide power, you should buy a new battery rather than wait for the old battery to fail completely.
  • Batteries should only be disconnected if the engine is off and the alternator is not running. Disconnecting a car battery while the alternator is running can cause a voltage spike that will damage sensitive electronic components in the vehicle, such as the PCM.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

When To Replace A Car Battery

  • Your car doesnt start. A new battery has a specified capacity to provide power. This capacity is referred to as the cranking amps rating of the battery. As a battery ages, the actual amps that a battery can supply becomes lower than its original rating Once the cranking amps fall below a critical threshold, it will be difficult or impossible to start your car.
  • Battery or charging system warning light is illuminated. Should a battery or charging system warning light illuminate, a mechanic should perform a few basic tests to determine if a battery replacement is needed.
  • Electrical components dont work. Once a battery has started to fail, and the voltage produced by the battery drops, then vehicle electrical components can malfunction, such as the security system. If you are experiencing electrical malfunctions, its a smart idea to have the battery tested.

Read Also: Car Battery Won T Charge

Caring For A New Ford Fusion Battery

Did you recently have a new 2017 Ford Fusion car battery installed? Great job! Now, help it last longer and stay charged by caring for it from the get-go. turning off all of the lights when you leave your vehicle, decreasing the number of short trips you take, keeping your battery posts clean, and not using electronics such as the radio and power outlets when the engine is off.

You May Like: How Long Does Gopro 9 Battery Last

What Is A Ford Fusion Key Fob Battery

A Ford Fusion key fob battery powers the key fob and provides owners of the Ford Fusion sedan with remote access to the engine start and the keyless entry systems. This auto accessory is suitable for the 2013-2020 second-generation Ford Fusion sedans. Key benefits and features of this product include:

  • Enables keyless entry to the Ford Fusion sedan.
  • Allows engine startup to be controlled remotely.
  • Improves vehicle security, as the key fob cannot be easily copied or attacked.
  • Helps you locate your vehicle via the Panic button.
  • Avoids traditional key-based issues, such as jammed keys.

S To Replace A Battery Terminal

For 2013 2014 2015 2016 2017 Ford Fusion Smart Remote Key Fob M3N ...

Step #1 Disconnect the terminals and remove the ends

Remove the negative battery terminal first, then the positive terminal. If the copper cable is molded into the old terminal, cut off the terminal with a hacksaw. If the cable was crimped onto the terminal, try unbending the crimp.

Step #2 Clean the copper wire strands with a wire brush to remove corrosion

Use a wire brush to clean up the wire strands until theyre bright. Then slide the heat shrinkable tubing onto the battery cable, followed by the compression nut.

Step #3 Insert the cable into the new terminal

Next, push the copper strands into the new terminal making sure no strands get caught.

Step #4 Tighten the compression nut

Hold the compression nut with a wrench while you screw on the terminal. Continue tightening until the compression nut is hard to turn. Finish the job by sliding the heat shrinkable tubing over the connection and shrinking it with a heat gun. The heat will shrink the tubing and activate the sealing adhesive.

Quick Compression Brand Battery Terminal

New battery terminals using QuickCables Quick Compression terminals

Compression terminals are a bit harder to find. NAPA stores carry the Quick Compression brand terminal made by QuickCable shown here.

Read Also: Places That Replace Watch Batteries

Ford Explorer Oem 3 Button Key Fob

This is a Factory OEM Ford Explorer 3 Button keyless entry remote, aka key fob.

Genuine OEM key fob remote with a new key.

Must be programmed by a professional automotive locksmith or dealership.

Expect professional programmers to charge programming fees.

OEM Key Fobs:

We are proud to offer true OEM key fobs direct to you at up to 80% off dealer prices. There is a catch though, so here it goes:

You need to know the only way to get a NEW OEM key fob is to go to a dealer or authorized reseller of OEM parts, and you will pay dealer prices if you do this and spend hundreds of dollars.

The key fob you are going to purchase from us is used or as we like to say previously loved. We recycle OEM key fobs and put them through a rigorous refurbishing process so we can guarantee our products and offer them at a reasonable price along with saving the environment. Oh, and we are not robbing you of your hard earned dollars like the stealership does. So if you are good with all of this what are you waiting for? Make your life easier, order a key fob from us and save the world!

If My Watch Is Under Warranty Is The Battery Covered

Batteries are not normally covered under warranty. Warranties for most brands cover mechanical parts and manufacturer defects only.

What you should know though is if you have someone replace the battery at a local repair shop you could technically void your warranty if your watch is still covered. Most companies consider anyone doing any type of maintenance on a watch other than an authorized service center grounds for voiding the warranty.

It may seem like a simple task to swap it out, but timepieces have complicated internal components. Once you open the back case, you could introduce dust into into which could cause issues. If you are concerned about keeping your warranty in tact, an authorized battery swap is advised.

Also Check: Does Whole Foods Sell Batteries

Larry H Miller Super Ford Salt Lake City Battery Replacement & Ford Batteries For Sale

Call Larry H. Miller Super Ford Salt Lake City at 3858812581 or schedule battery service online for the fastest battery replacement in Salt Lake City UT. At Larry H. Miller Super Ford Salt Lake City, our service team is comprised of Ford adept certified technicians that can help diagnose what is wrong with your battery. Our Ford factory-trained mechanics can change your Fusion battery promptly at exceptionally ambitious prices.We will check your battery for any simple fixes such as delicately examining your battery for corrosion build-up before recommending a full battery replacement. Our primary objective is customer service unlike many other auto repair shops. Every Now And Then it is just a poor battery connection and tightening or reconnecting loose components might get your 2017 Ford Fusion started again. Outstanding service and inexpensive prices are just two of many reasons people do business with Larry H. Miller Super Ford Salt Lake City.

Read Also: Cordless Drill With Battery And Charger

How Does A Car Battery Work

How to remove and replace your battery in a 2017 2.7 Ecoboost Ford Fusion Sport

The battery in your vehicle is there to provide a jolt of electrical energy to start the engine and to provide engine-off accessory power for a limited amount of time. Once the engine is running, the alternator takes over topower the accessories and charge the battery. Car batteries typically feature six connected cells in a lead-acid formulation, or up to 12 cells in a 24-volt system found in heavy trucks or other large vehicles.

Recommended Reading: How To Replace Dyson V6 Battery

How Do You Know If Your 2017 Ford Fusion Needs A New Battery

The most common symptoms of bad 2017 Ford Fusion batteries are if your car is slow to start after turning the key, or if your battery cables and connectors show signs of heavy corrosion. You may still notice a boisterous clicking sound when turning the key or if your electronics work but the car won’t start. These are all tell tale signs of failing batteries on your 2017 Ford Fusion. Give our experts at a call or book an online appointment here.

Answers To Your Fusion Car Battery Questions

Get answers to common car battery questions, from Firestone Complete Auto Care. If you have a Fusion-specific battery question, pay us a visit. Our expert techs have the answers you need.

  • Why wonât my Fusion battery hold a charge? A battery that won’t hold a charge is almost as good as dead. The battery may be too old. Or, you may have a habit of leaving your car doors open and the dome lights on during the night. Stop by for a complimentary battery check at your nearest Firestone Complete Auto Care and get a handle on your car batteryâs health.
  • What do you do with my old Fusion battery? We recycle it, taking care of both your car and the Earth.
  • How much will replacing my Ford Fusionâs battery cost if I get a DieHard battery? Get affordable prices on Ford Fusion batteries by using one of our limited-time battery deals. Plus, all DieHard car batteries come with a free replacement warranty and extra coverage with DieHard Assurance.
TIRES

Read Also: Does Costco Sell Car Batteries

Ford Explorer Key Fob Programming

Once the car is started the Intelligent Access key can be removed and the mat and any cups. Every two years or so or when the battery is low you may need to change the key battery.

How To Change A 2000 2010 Ford Explorer Key Fob Remote Battery Part 3b 2l3t 15k601 Ab Key Fob Programming Instructions Key Fob Fobs Key

You May Like: Does Autozone Replace Key Fob Batteries

Check Battery And Reset The Security System

Batería Tested Tough Max para Ford Mustang Ford Fusion Lincoln MKZ ...

After installing your new battery, test it and reset your Fords security system. You can do so by using it to lock and unlock your vehicle. After an effective installation, you should hear the door locks and see the parking lights in a response to the remote instructions. Update your Fords service records with the battery change.

Hearst Autos Research, produced independently of the Car and Driver editorial staff, provides articles about cars and the automotive industry to help readers make informed purchasing choices.

Also Check: Ntb-national Tire & Battery Greenville

How To Fix The Ford Fusions Battery Draining Problem

take your car to a professional mechanicwhy your battery is unable to hold a chargebetween $175 and $185

  • Locate your vehicleâs battery by referencing your ownerâs manual.
  • Turn the engine off.
  • Loosen the bolt holding the black cable with a wrench. You should be able to remove the cable by gently twisting and pulling.
  • Remove the red cable by repeating the previous step.
  • Using a wrench or ratchet, remove the battery.
  • Install the new battery by reversing the order of the previous steps, and youâre done!
  • A parasitic drain essentially means an electrical component in your car is continually sucking power from your battery, even when the engine is turned off. A mechanic can determine if this is the case.
  • Faulty alternators are often linked to battery issues. Repairing or replacing your alternator may be the right option.
  • Corroded battery cables and terminals dramatically impact the operation of your battery. Make sure everything is hooked up properly and inspect the terminals for signs of damage.

MORE:

You May Like: Battery For Audi Key Fob

Cost At The Mechanic: $1800 To $8000

  • Parts: $1,500 to $7,500
  • Labor: $300 to $500

A mechanic can replace the hybrid battery in your Ford Fusion Hybrid in a matter of an hour or two because they have the proper tools and training. One thing to consider when replacing the battery is whether to repair your existing battery or replace it entirely. Another is if you choose to replace it, whether to go with a new battery or a used battery. If your Fusions battery is under warranty, Ford will make the right decisions for you at no cost. However, if youre paying out-of-pocket for this repair, you may want to consider other options to save some money.

Read Also: Replace Battery In Honda Crv Key

Read Also: Car Battery At Home Depot

How To Unlock And Start Your Ford Vehicle After Its Key Fob Battery Dies

Many new Ford models are outfitted with Push Button Start technology and keyless entry, which means that all you need is a functional key fob to get inside and start the engine. When your key fob battery dies, however, dont worry! There are still methods to unlock your model and start up.

First, to get inside your Ford, you may want to check whether you have a Ford SYNC Connect® equipped vehicle and the FordPass app installed on your smartphone. From there, you can pair it up to your vehicle. Vehicles equipped with Sync Connect 2016 model year forward can remotely unlock their vehicles using the FordPass app without the need of your key key fob. It can also Remote Start your vehicle and even find and pay for parking!

You May Like: Deep Cycle Battery San Diego

Ford Fusion Se Battery

2017 Ford Fusion key fob battery replacement

2012 ford fusion battery. Fusion ford se transmission 5l battery replacement fluid cyl check replace headlight change signal turn bulb oil level brights. Fusion ford hybrid test road auto123 ok 2017 ford fusion se battery

2014 Ford Fusion Hybrid – Our Review | Cars.com. 17 Pics about 2014 Ford Fusion Hybrid – Our Review | Cars.com : Battery Replacement: 2013-2016 Ford Fusion – 2013 Ford Fusion SE 2.0L 4, 2017 Ford Fusion Hybrid Road Test and Review | Autobytel.com and also 2017 Ford Fusion Hybrid Road Test and Review | Autobytel.com.

Recommended Reading: Testing Car Battery With Multimeter

Is It Safe To Drive With The Battery Light On

The purpose of the alternator is to charge your 2017 Ford Fusion battery while you are driving. When the alternator isn’t working correctly, it can cause the battery to utterly drain all its power, leaving you stranded if the vehicle is turned off. Be sure to turn off the radio, air conditioner, and the lights unless you are driving at night. If your 2017 Ford Fusion battery warning light comes on while driving, be sure to turn off your accessories, so the battery doesnt drain further. The warning light usually means that the alternator isnt working correctly, meaning you are operating solely on battery power.It’s again very potential that your 2017 Ford Fusion serpentine belt has malfunctioned. If you have multiple warning lights come on including the battery light, then pull over to a secure location if potential.Another possible sign that could point to the serpentine belt as a cause for the battery warning light, is if steering becomes difficult or feels heavy. If the dash lights reveal overheating, then the water pump was on that belt too. If you’re near Salt Lake City and need immediate service, give Larry H. Miller Super Ford Salt Lake City a call at 3858812581. We can even arrange to have your 2017 Ford Fusion brought in to us.

Are There Signs A Battery Is Dying

The most common sign that indicates your battery needs to be changed is the watch losing time. You will notice in quartz watch for example, the time will get slow. Sometimes the hands will start to stick a little. As soon as you notice an indicator like this, you should move to replace the battery before it dies.

You May Like: Best Price For Car Batteries

Read Also: Electric Vehicle Battery Replacement Cost

How Do Mechanics Replace The Battery

  • A temporary power source might be installed to avoid the possibility of losing radio presets or stored data in the PCM while the battery is out. When the battery is already completely dead, this step is unnecessary.
  • The vehicles negative cable is removed from the battery, followed by the positive cable. The battery tie down system is loosened and the old battery removed.
  • Cable ends and wiring are carefully inspected to ensure cleanliness and no corrosion. In some cases, corrosion can be extreme and the cable may need to be replaced or wiring repaired.
  • The new battery is installed and the tie down system is reinstalled. Anti-corrosion compound is applied to the battery terminals. The positive terminal is reconnected followed by the negative terminal.
  • Some vehicles, for example some models of BMW, VW, and Audi, may require PCM programming to input battery parameters. This step, performed using a specialized scan tool, is necessary to maximize battery life and prevent electrical system malfunctions.
  • The car is started and charging system output is measured and compared against the factory OEM specification to ensure that the new battery will properly recharge. Generally, charging output will be in the range of 13.8 to 14.8 volts but the exact specifications vary by make and model.

Related Posts