Change Subaru Key Fob Battery

Share This Post

How To Replace Your Subaru Key Fob Battery

Subaru Key Fob Battery Replacement ( Keyless Entry Trick) Cars Simplified

Replacing the battery in your Acura key fob is a straightforward but not always easy process. Key fobs are sealed tight to help durability and keep water from getting into the electronics, and there isn’t always an obvious way to open them up. You may also need to reprogram your key with your vehicle after changing the battery in some cases. Our Parts team has the tools and knowledge to replace the battery in your specific key fob correctly. Stop in, and we will gladly help you!

How To Replace Battery In Subaru Key Fob

CR2032 3V and CR2025 3V batteries are common replacements for Subaru key fob batteries.

Similarly, What kind of battery goes in a Subaru key fob?

CR2032 3V and CR2025 3V batteries are common replacements for Subaru key fob batteries.

Also, it is asked, What battery does a 2018 Subaru Outback key fob take?

How to change the battery in the Subaru OutbackSilver Sideskey fob For a step-by-step guide on how to replace the battery in your key fob, see the video below. You will need 1 CR2032 battery.

Secondly, Can I replace the battery in my key fob?

Yes, you can change the batteries in your key fob, and its a lot simpler than you would think. A little flat-tipped screwdriver and a fresh battery are all youll need.

Also, How do you change the battery in a 2015 Subaru Outback key?

Capitol Subaru is here to assist you How to Change the Battery in a Subaru Key Fob Invest on a fresh 2032 battery. Use a metal key or a flathead screwdriver to open the key fob. Inside the fob, look for the flat circular battery. Remove the tiny tabs that hold the battery in place. Assemble the key fob again.

People also ask, How do you start a Subaru with a dead battery?

If the battery on the fob is dead and you can start it, hold the fob to the start button and push the button. If its the automobile, open the hood and jump it like any other vehicle

Related Questions and Answers

What Size Do Batteries Go In Key Fobs

Youll know its time to change the battery in your Subaru key fob when the remote no longer opens or locks your doors or sets off the panic alarm. Its a pretty straightforward process that only takes a few minutes. You can change the battery yourself with just a few simple tools. You need a small Phillips head screwdriver and a new CR2032 battery. Start by removing the Phillips head screws from the back of the key fob.

Then, pry open the case and take out the old battery. Be careful not to lose the small spring that sits next to the battery compartment this is what helps keep the door lock button in place. To install the new CR2032 battery, simply insert it into the compartment with the positive side facing up and replace the cover and screws. Thats it! Your Subaru key fob will be as good as new.

Also Check: Enphase Battery Vs Tesla Powerwall 2

How To Program A Subaru Key Fob

If you need to replace your Subaru key fob or program a new one, you may be wondering if you can handle this task in your Lakeland garage. For drivers with a new Subaru, an authorized Subaru dealershipservice center will need to complete the Subaru key fob programming process. If, however, your Subaru is a bit older, then programming the key fob at home in Lakeland Heights or Winter Haven may be possible. Subaru Lakeland covers the steps to follow below, in addition to discussing how to replace a Subaru key fob battery.

Can You Buy Subaru Replacement Key Fob

2015 Subaru Impreza Key Fob Battery Replacement

You might find that even after changing the battery, the key fob does not work. You check the polarity of the battery and everything is in the right order, yet the key fob does not work. This is a pointer to internal damage to the key fob.

When the key fob is damaged beyond repair, the key fob is lost or you just need an extra key fob, you can buy a new Subaru key fob. You can get a new subaru remote from either of the following:

1. From Subaru dealership.

In this case you will drive your Subaru to the dealership and buy the new key fob. The dealer will cut the emergency key found in the key fob and program the new key fob to sync with your car. This will definitely come at a premium cost to you but will be hustle free and will be accomplished within a day.

2. From online retail store.

In this case, you will need to place the order online and have the key fob delivered in 1-2 days. The key fob comes with a blank emergency key and the remote is not programmed to be used in your car.

You will need to visit the locksmith to have the key cut and you can program the key fob as outlined below and save on cost. The new key fob comes with instructions as to how the programming will be done.

Ordering a new key fob online will cut the dealer cost by as much as 50%. It is the cheaper and most convenient method of getting a new Subaru key fob.

How to Reprogram Subaru Key FOB?

Test the key fob to see if it is working well. If they key fob is not working, it may need to be reprogrammed.

Recommended Reading: How To Charge Toyota Prius Hybrid Battery

What Kind Of Battery Does My Key Fob Need

No matter what kind of car you drive, your key fob is essential for your day-to-day life. This small device allows you to unlock your doors, start your engine, and even open your trunk all with the push of a button. But like any battery-powered device, key fobs eventually need to be replaced. So, what kind of battery does my key fob need?

The most common types are CR2025 and CR2032 3-Volt batteries. You can find the exact type in your vehicles owners manual or by checking what kind of the old key fob battery is after removing it. You can find a new key fob battery for your car at your local AutoZone, no matter which type you need.

Weve got you covered with a wide selection of batteries in stock no matter what kind of car you drive. So next time your key fob starts to act up, dont worry just head to AutoZone for a new battery. Well help you get back on the road in no time!

How Long Does Key Fob Battery Last

The key fob battery is supposed to last several years before a replacement is needed. However, the battery life span depends on several factors such as how often the key fob is being used. The more frequent the use, the shorter the period it will last.

The environment in which it is operating also affects the lifespan of the key fob battery. In hot and humid areas, the battery will not last long like in cold environment. Extremely low temperatures may also affect the lifespan of the key fob battery.

You May Like: Interstate Batteries Srm-24 Marine/rv Deep Cycle Battery

Subaru Key Fob Not Working 5 Causes

Quick Navigation

Is your Subaru key fob not working? It can be frustrating and dangerous, especially if your child or pet is locked inside the car.

Car key fobs are handy tools that let you unlock your vehicle, open the trunk or even remotely start your car engine.

Faster than the standard car key and with an inbuilt panic button, we now rely on key fobs for safety and convenience every time we drive.

But what happens if the key fob stops working? Perhaps it loses signal, malfunctions, or needs replacement.

Can it be reprogrammed? Weve answered these questions and more in this article!

How To Change The Battery In The Rectangular Subaru Key Fob

EASIEST Subaru Key and Fob Battery Change. No Tools needed!

If you have a Subaru with a rectangular key fob, heres how to change the battery:

1. Start by removing the key from the key fob.

2. Next, use a small flat-head screwdriver to pry open the back cover of the key fob.

3. Once the back cover is off, you should see a small battery inside.

4. Use a small pair of pliers to remove the old battery and then insert the new one, making sure the + and – signs are facing the correct way.

5. Finally, replace the back cover and screw it back on.

Your Subaru key fob should now be working properly again!

Recommended Reading: Arlo Essential Spotlight Camera Battery Life

Replace Key Fob Battery

As mentioned earlier, if you find that your key fob isnt working, the simplest solution is to try and replace the batteries.

While this might not outrightly resolve the issue, its an important troubleshooting step. A dead battery is the most common cause of a key fob not working.

You have to open the shell, check out the type of battery you need and then purchase pair from the auto parts store.

Use A Screwdriver To Open The Housing

Youd need to open the housing to uncover the control module. While you can directly use the screwdriver for the purpose, it is better to tape it to prevent damaging the control module.

Now insert the screwdriver tip to separate the housing. As soon as you split it into two, youll find that one houses the control module while another is used as a covering.

Also Check: Go Pro Hero 8 Batteries

What Type Of Battery Does The 2017 Subaru Impreza Use In Its Key Fob

If youre the owner of a 2017 Subaru Impreza, you might be wondering what type of battery it uses in its key fob. Heres a quick guide to help you out.

The 2017 Subaru Impreza uses a CR2032 battery in its key fob. This is a 3-volt coin-type battery thats widely available at most electronics stores.

To replace the battery in your key fob, start by removing the keychain. Then, use a small flathead screwdriver to pry open the back of the key fob. You should see the battery inside.

Gently remove the old battery and then insert the new one, making sure that the positive side is facing up. Once the new battery is in place, close up the key fob and reattach the keychain.

If your key fob starts to act erratic or doesnt work at all, chances are its time for a new battery. By following these simple steps, you can easily replace the battery in your 2017 Subaru Imprezas key fob.

How To Change The Battery In A Subaru Key Fob

How to Replace the battery for 2010 Subaru Outback Key fob ...

CR2032 3V and CR2025 3V batteries are common replacements for Subaru key fob batteries. There are various varieties to utilize, but it is critical to consult your cars handbook to determine the best battery type for your fob.

Similarly, What battery goes in a Subaru key fob?

CR2032 3V and CR2025 3V batteries are common replacements for Subaru key fob batteries. There are various varieties to utilize, but it is critical to consult your cars handbook to determine the best battery type for your fob.

Also, it is asked, How do you change the battery in a 2018 Subaru key fob?

To access the fob, remove the glove box key by pressing the silver button and using it to push open a tiny hole that is disclosed. The battery may then be removed and replaced from there. Easy as pie!

Secondly, How do you open an old Subaru key fob?

Subaru Key Fobs from the past Look for a little gap between the front and rear of the key fob in the seam. With a little flathead screwdriver, pry the key fob open. Remove the old battery and replace it with the new 2025 battery. Make sure the new battery is facing the same way as the old one.

Also, Can you start Subaru without key fob?

Registered. In the event that the fob fails, the automobile can give electricity. You must push and hold the button for a few seconds before pressing START.

People also ask, What kind of battery does 2018 Subaru key fob take?

3V Lithium CR2032 Battery

Related Questions and Answers

Recommended Reading: Change Battery In Vw Key Fob

What Battery Goes In A Subaru Key Fob

Your key fob is an important part of your car, and the battery is one of the most important parts of the key fob. So, what battery goes in a Subaru key fob?

The most popular batteries for Subaru key fob battery replacement are CR2032 3V and CR2025 3V. These are the most common batteries that are used in key fobs, and they are both 3-volt batteries.

However, there are other types of batteries that can be used in a Subaru key fob. It is essential to check the manual of your car to know the perfect battery type for your fob. Depending on the model of your car, the manual will recommend a different type of battery.

The CR2032 3V battery is the most common type of battery used in key fobs. It is a small, coin-shaped battery that is 3-volt. This type of battery is often used in watches, calculators, and other small electronic devices.

The CR2025 3V battery is another common type of battery used in key fobs. It is also a small, coin-shaped battery that is 3-volt. However, the CR2025 battery is slightly larger than the CR2032 battery.

It is important to note that there are other types of batteries that can be used in a Subaru key fob. If you are unsure about which type of battery to use, it is always best to consult the manual of your car. The manual will have the most up-to-date information on the best type of battery to use in your car.

How Do Locksmiths Program Key Fobs

What Methods Do Locksmiths Use to Program Car Keys? Locksmiths interface with your vehicles computer through the OBD port, which is normally situated beneath the steering column, to program car keys and FOBs. The cost of programming a car key ranges from $25 to $100, depending on who provides the code, the vehicle, and the locksmith.

Also Check: 2008 Toyota Camry Hybrid Battery

Top Reasons To Replace Subaru Key Battery

There are some common problems with the key batteries that you should consider before purchasing replacement parts. Today I am giving some top five reasons why you should replace your Subarus key battery.

  • When you have an older model of Subaru, the key battery may not last long. It could start fading out after two years or so.
  • Some people say that their key batteries dont work at all. If this happens, then there is no point in buying another one.
  • There are chances that your key battery may stop working due to overcharging. Overcharging can damage the battery and cause it to fail.
  • Sometimes, the key battery gets damaged by water. If this happens, you must dry up the battery immediately.
  • A dead key battery doesnt provide power to your vehicle. Therefore, it is very essential to check the condition of your key battery.
  • If you find any of these issues with your key battery, then you need to replace it. Otherwise, you may end up spending an exorbitant amount on repairing your vehicle.

    Insert The Mechanical Key And Test

    Subaru Forester / Outback / Impreza Key Fob Battery Replacement – DIY

    Now return the mechanical key to its original place. Fortunately, itll be a lot easier than the removing process.

    But your battery replacement doesnt end here. Testing the key fob is a must to ensure appropriate battery replacement. Use it to lock and unlock the car. Besides, try other features to ensure its working correctly.

    If the key fob fails to function, your vehicle may have an underlying issue. While its a bitter pill to swallow, cars being gadgets are prone to technical problems.

    You can always contact a professional mechanic to identify and fix the underlying vehicle problems, and if your car is insured, its even better the company takes responsibility for repairs.

    Also Check: Checking Car Battery With Multimeter

    How To Replace The Battery In A Keyless Entry For A Subaru Forrester

    When the keyless entry remote for your Subaru Forester begins to weaken or fails completely, you should replace the battery as soon as possible. The remote uses a CR2025 battery available from most major retailers and electronics stores. When you replace the battery in your Forester remote, you need to synchronize the remote to the system again for it to work properly.

    Step 1

    Insert a flat-bladed screwdriver or butter knife into the indent slot at the wider end of the keyless entry remote. Twist sideways to separate the two sides of the remote and expose the battery.

    Step 2

    Lift the old battery out of the remove. Insert the replacement battery with the negative side facing up.

    Step 3

    Push the two sides of the remote together until they click, locking together.

    Press the “Lock” or “Unlock” button on the keyless entry system six times in rapid succession to synchronize the remote with the keyless entry system.

    References

    • “2010 Subaru Forester Owner Manual” Subaru of America, Inc 2009

    Things You’ll Need

    Fix Your Subaru Key Fob Not Working

    For starters, before you tear the key fob part trying to fix the problem, you should check to find out the exact reason why the key fob isnt working.

    Subaru owners are always in a hurry to get back on the road, either for the thrill or because they are running late for work.

    In the haze of this hurry, there are some things a Subaru driver might do that can mislead them into thinking that the key fob is not working.

    First, you might have reached for a key fob belonging to another car, or the button youre pressing isnt the right one.

    You should take enough time to evaluate the dilemma youve just found yourself in so you can know exactly why the key fob is not working.

    Here are a few things you can do to diagnose your key fob not working.

    Don’t Miss: 3/4 Hp Garage Door Opener With Battery Backup

    Related Posts