How To Put Battery In Key Fob

Share This Post

Q6 How Often Do You Change The Car Key Battery

How To Change Ford Key Fob Battery

Ans. The battery life in most car keys is around 3 to 4 years. It also depends on the amount of usage. Also, the key fob should not be kept inside the car or near the car on a hook when the car is parked. This is because the car key fob will continuously be sending signals to the receiver and will shorten the battery life.

Troubleshoots In Changing The Battery In Chevy Key Fob

If your Chevy key fob has a dead battery, youll need to know how to change it out. Here are some quick and easy troubleshooting tips.

First, make sure that the battery in your key fob is actually dead. You can do this by pressing the button on the key fob. If the button doesnt work, then the battery is most likely dead and will need to be changed.

Next, locate the small Phillips head screws on the back of the key fob. There are usually two of them. Use a small Phillips head screwdriver to remove the screws and take off the back cover of the key fob.

Once the back cover is off, youll see the battery inside. Carefully remove the old battery and replace it with a new one. Make sure that the positive side of the new battery is facing up before you put the back cover back on and screw it into place.

Then, press the button on your key fob to test it out. If it works, then youve successfully changed the battery in your Chevy key fob!

How Much Does It Cost To Replace A Key Fob

Theres no simple answer, but few modern key fobs are inexpensive. Even basic remotes may require special programming with computer software only accessible by a dealership.

Though the repair wont take more than a few minutes to replace, this can get expensive.

Kelley Blue Book contacted dealerships across the country for replacement costs of key fobs for some popular and high-end models. Quotes we got for replacing key fobs for a 2020 Subaru Forester with a push-button start ranged from about $200 to $400. A 2020 Toyota Sienna fob was about the same. However, dealers quoted as little as $150 to replace a 2017 Honda Accord key fob.

Several BMW dealers said that the more advanced security features embedded in the fob for a 2020 X5 justify the roughly $500 they charge to replace and program one. If you think thats a lot, consider that the crystal fob Aston Martin included with some of its models might cost $2,000 to replace and reprogram.

Also Check: How Long Does Galaxy Watch 4 Battery Last

These Are The Basic Principles Of A Key Fob Regarding Their Design Manufacture And Use:

  • A key fob is a remote control with a radio frequency ID chip and an antenna. The key fob uses radio frequencies to send signals to another radio frequency ID reader device inside the car that controls the locking mechanism. Each key fob transmits a specific RFID information tag that can be read by the reader device inside the car.
  • When the button on the key fob is pressed, the key fob will transmit a radio frequency ID message to the receiving device inside the car. If the radio frequency that is transmitted from the key fob corresponds to the receiver mechanism that is programmed to accept it, the unlocking mechanism will open the door lock.
  • Radio frequency ID key fobs are very versatile and can be programmed for various purposes. The functions such as unlocking a specific door or firing up the engine can be programmed into the keyless system. In most of the cases, the key fob unit has multiple functions assigned to it using different buttons.
  • Usually, the key fob will be contained in a plastic enclosure that is small enough to fit in your hand. Some key fobs dont have any buttons, instead they have proximity sensors that work when passed in front of the receiver electronic lock/unlock mechanism. Other types of key fob systems use buttons to transmit a radio frequency that is specific to the lock/unlock mechanism. Each button on the key fob performs a certain function like unlocking the vehicle, locking it or starting the engine and even opening the trunk lid.
  • Insert The Replacement Battery

    Changing a Ford Focus (2002) Key Fob Battery

    Typically, the negative side of the key fob battery is facing down, and the positive side is facing up. However, this may not be the case for all key fobs. For this reason, I advised earlier to take note of the polarity of the old battery that mental picture will serve as your foolproof guide on how to position the new battery.

    On the bright side, some Jeep key fobs have labels printed into the battery socket providing instructions on how the battery should be fitted.

    Also Check: Best Android Phone Battery Life

    How Do You Replace The Battery In A Car Key Fob

    While the black or silver exterior of a key fob may be somewhat intimidating, generally speaking replacing the battery is a straightforward process. Most key fobs will have a seam in the back or the side showing where they come apart. Using a small tool, like a screwdriver or a pliers, you can pry the pieces apart. Most batteries in key fobs are the small round kind that are used for watches and small electronics. The exact type used may vary depending on the fob.

    How To Replace The Battery In Your Cars Key Fob

    If your car key fobs range has diminished, the buttons arent responding to your touch, or the vehicle is having trouble recognizing its proximity, the key fob battery is probably dead.

    Yes, it is possible to replace the battery in your key fob, and its easier than you think. All you need is a small, flat-tipped screwdriver and a new battery.

    Don’t Miss: Replaced Batteries In Honeywell Thermostat

    Battery Place Near Me

    With over 700 stores throughout the United States and Puerto Rico, theres sure to be a Batteries Plus Bulbs nearby. Stop in today for the best selection of energy and lighting products. Be sure to ask about how to save your business time and money by opening up a commercial account. Our experts are always on hand to answer your questions and help you find exactly what you need.

    *Smart home & key services vary by location check your nearest store for eligibility.

    Read Also: Dead Car Battery Or Alternator

    Notice How The Battery Fits

    How To Change An Infiniti Key Fob Battery-Tutorial

    Every battery has a positive and negative side and if you put the wrong connector down, the charge cannot go into your device and make it work. That is why its important to see whether the positive or the negative is supposed to be up, and put your new battery the same way.

    Here at Third Coast Auto Group , we recommend that you search for directions on your specific key fob battery . These directions are a good overview, but if you have push-button ignition, or a key built into your key fob then it might be valuable to check out specific details . And if you are looking for a new-to-you used vehicle, check out our inventory in the Austin area!

    Don’t Miss: Does Costco Replace Car Batteries

    How To Change Jeep Key Fob Battery

    Generally, Jeep key fob batteries last between three to four years. But depending on how frequently it is used, the battery could die out much sooner. If you need to press the keypad repeatedly to lock your car doors or your key fob no longer works within 45 feet of your vehicle, it is high time for a battery replacement.

    Depending on the model, year, and trim of your Jeep, it may come with one of the following key fobs:

    Jeep Models
    Pear-shaped, 3V CR2016 1999 2004

    Except for the shape and some features, there is little to no difference between these key fob designs. That said, the steps required to change their battery are pretty similar. In this section, however, we will cover steps applicable to a fixed-key Jeep key fob :

    How To Change Battery In Jeep Key Fob

    Disclosure: We may get commissions for purchases made through links in this post.

    The Jeep key fob is part of your vehicles keyless entry system. Unlike in the olden days when manually locking and unlocking car doors was required, recent-year Jeep models with key fobs do this for you electronically. Hence, it would be beneficial to familiarize yourself with this innovative feature and to know when it is time for a battery replacement. This guide will surely help you achieve these objectives.

    Here are seven steps on how to change the battery in a Jeep key fob:

  • Pop the Jeep key fob open with a screwdriver.
  • Apply pressure on the screwdriver as you pry it open.
  • Remove the Jeep key fob battery from its housing.
  • Insert the replacement battery.
  • Reassemble the key fob components.
  • Snap the key fob housings together.
  • Reprogram your Jeep key fob .
  • If left unaddressed, a key fob with a poorly working battery will hinder your ability to lock and unlock your car doors remotely. Worse, it can trigger your car alarm or cause a no-start issue for your vehicle. Both are situations no one would ever want to be in, which makes knowing how to replace the battery in a Jeep key fob all the more significant.

    Also Check: 2007 Buick Lucerne Battery Location

    Your Battery Begins To Run Out Of Power

    If you notice that your keys are not responding as quickly, or at all, to your commands and press the buttons over and over again with no change, then it is time for a new battery. A dead key fob is an indicator that there is a problem with the battery.

    You can replace your Subaru key fob battery yourself if you have some basic knowledge of car parts. You can get replacement batteries at any auto parts store for less than $5-$20 depending on the quality of the battery.

    How To Install The New Battery In The Key Fob

    How To Change Battery In Chevy Key Fob 2016

    Spring is here and along with it, warmer weather! Warmer weather means more time spent outside, and more time spent outside means your car key fob battery is going to die sooner. So, today were going to show you how to install the new battery in the key fob. To start, youll need a flathead screwdriver.

    With the screwdriver, pop opens the back of the key fob. Once the back is open, youll see the battery. Using the screwdriver, carefully pry the old battery out and dispose of it properly. Take the new battery and insert it into the key fob, being careful to line up the positive and negative sides correctly.

    Once the new battery is in place, close up the back of the key fob with the screwdriver. And thats it! Youve now successfully installed a new battery in your key fob. Thanks for following along and feel free to leave any questions in the comments below.

    Recommended Reading: Honda Car Key Battery Replacement

    How Do I Replace The Battery In The Key Fob For My Ford

    For instructions on how to replace the coin-type three-volt lithium battery in your key fob, refer to your Owner’s Manual under “Keys and Remote Control.”


    • Do not wipe off any grease on the battery terminals or on the back surface of the circuit board.
    • Refer to local regulations when disposing of batteries.
    • Replacing the battery does not erase the programmed key from the vehicle.

    If you need assistance, take all your keys to your Ford Dealer.

    How To Replace The Battery In A Key Fob

    This article was co-authored by Shawn Fago. Shawn Fago is a Master Locksmith and the Founder of Noble Locksmith, a nationwide locksmith company based in San Diego, California. With over seven years of experience, he provides commercial, residential, and automotive locksmith services to customers. Shawn attended California State University, Fullerton. This article has been viewed 197,088 times.

    No matter what type of key fob you have, you can replace the battery in a few minutes. The technique to open the fob and the battery you need differs slightly depending on the specific key fob you own. Pry open the fob, then swap the old battery out for a new one. Your key fob should then work as intended once again.

    Also Check: National Tire And Battery Dunbar Wv

    How To Change The Battery In A Subaru Key Fob

    CR2032 3V and CR2025 3V batteries are common replacements for Subaru key fob batteries. There are various varieties to utilize, but it is critical to consult your cars handbook to determine the best battery type for your fob.

    Similarly, What battery goes in a Subaru key fob?

    CR2032 3V and CR2025 3V batteries are common replacements for Subaru key fob batteries. There are various varieties to utilize, but it is critical to consult your cars handbook to determine the best battery type for your fob.

    Also, it is asked, How do you change the battery in a 2018 Subaru key fob?

    To access the fob, remove the glove box key by pressing the silver button and using it to push open a tiny hole that is disclosed. The battery may then be removed and replaced from there. Easy as pie!

    Secondly, How do you open an old Subaru key fob?

    Subaru Key Fobs from the past Look for a little gap between the front and rear of the key fob in the seam. With a little flathead screwdriver, pry the key fob open. Remove the old battery and replace it with the new 2025 battery. Make sure the new battery is facing the same way as the old one.

    Also, Can you start Subaru without key fob?

    Registered. In the event that the fob fails, the automobile can give electricity. You must push and hold the button for a few seconds before pressing START.

    People also ask, What kind of battery does 2018 Subaru key fob take?

    3V Lithium CR2032 Battery

    You May Like: Emergency Exit Lights With Battery Backup

    The Basics Of A Chevy Key Fob

    How to Change a Key Fob Battery

    A Chevy key fob is a small, hand-held electronic device that allows you to remotely control various functions of your Chevrolet vehicle, such as locking and unlocking the doors, starting the engine, and opening the trunk.

    It typically consists of two parts: a metal key blade that fits into the ignition, and a small plastic transmitter with buttons for controlling the various functions. In most cases, the key fob batteries can be replaced by following a few simple steps.

    First, use a small flathead screwdriver to pry open the back of the key fob. Next, remove the old battery and insert the new one, being sure to orient it correctly. Finally, close up the key fob and test the buttons to make sure theyre working properly. If your key fob is still not working after replacing the battery, it may be time to consult a professional.

    Don’t Miss: Change Batteries In Key Fob

    Then Put Back On The Cover Plate And Test Out Your Remote By Closing And Opening Vehicle Doors From Afar

    The cover plate should snap back into place and lock, but if it doesnt, try flipping it over and pressing down from the other side. If that still doesnt work, contact your dealership for help.

    Now test out your remote by closing and opening vehicle doors from afar. If youre having trouble getting the remote to work properly after changing the battery, contact your local dealership for assistance.

    Also Check: How To Change Battery For Mercedes Key

    Identify And Procure The Correct Battery Type

    In most key fobs, the battery is called a button or coin cell battery because of its shape and size. The identification number is etched into the flat side of the battery. This ID number is three to four digits long, and the new battery must have the same number. The battery most commonly used in key fobs is the CR2032 battery, but other widely used button batteries include the CR2450, CR2025, CR1616 and CR2016.

    Read Also: Battery Wharf Hotel Boston Waterfront

    Can You Unlock Your Car With A Dead Key Fob

    Yes! Having a dead battery in your car key fob does not mean that you are left stranded. Car manufacturers have foreseen this situation and built-in fail-safes to ensure you can unlock your car even in such a situation.

    Heres what you should do:

    • All car manufacturers include a mechanical key in the cars key fob. This can be accessed by sliding/pressing a small button usually located on the side of the key fob, which will remove the fob cover.
    • Once you get the mechanical key out of the fob, insert it into the key slot and turn it to unlock/lock your car.

    Mechanical keys are usually included in the key fobs of all major car manufacturers like Honda, Kia, Toyota, Mercedes, Ford, etc.

    Lightly Pry At The Notch Or Seam

    When does the key fob battery need replacing?

    When it comes to replacing a button cell battery for the key fob, you require one tool. Using a thin, small-flat-headed screwdriver, pry separate the two parts gently to open the key fob down the center.

    Most modern cars with transponder keys and fobs cant allow you to lock the keys inside your car. However, it would help if you were ready in case the worst happens.

    Turn the key counterclockwise on the ON position, lift the dash, and open the cover to expose the key blade. Remove the metal plate to get access to the battery compartment.

    Put the car key in the ignition to disconnect it from the car battery and leave it for some time to allow the battery to cool down. The car wont remotely start without this key, and if you pull it out from the ignition, the car wont start. The car wont turn on in that state without pressing the e-lock button.

    Detach the metal plate on the panel to access the fob battery. Squeeze the clips on the two sides of the plate and pull down on it.

    Recommended Reading: 2017 Dodge Journey Battery Location

    Related Posts